pipe flow experiment lab report

From the experiment it can be conclude that with decrease in area of flow there is an increase in velocity and decrease in the flow pressure of the fluid. Elperin et al 2002.

How To Write A Chemistry Lab Report Check More At Https Nationalgriefawarenessday Com 24692 How To Lab Report Template High School Chemistry Labs Lab Report

Contaminate reagent bottles by using pipe ts contaminated with acetone known compounds or unknowns.

. The viscosity of the fluid also determines the characteristic of the flow becoming laminar or turbulent. Form this experiment the flow rate for the. In fluid dynamics Bernoulli.

The nearest power supply. General Safety rules to be followed in Fluid Mechanics Lab. Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full -- Part 2.

INSTRUCTION MANUAL F1-21 FLOW METER DEMONSTRATION F1-21 ISSUE 3 SEPTEMBER 2001 ARMFIELD LIMITED OPERATING INSTRUCTIONS AND EXPERIMENTS F1-21. Calculate the slope of these graphs using the equation of. However the device has studied by researchers for different purpose.

For Reynolds number from 2100 to 4000 the pipe flow will be considered a transitional flow. PhET sims are based on extensive education research and engage students through an intuitive game-like environment where students learn through exploration and discovery. FACULTY OF CHEMICAL ENGINEERING.

Measurement of fluid flow using small bore precision orifice meters. The experiment was conducted in order to demonstrate Bernoullis Theorem to investigate validity of Bernoullis Theorem when applied to the steady flow of water in tapered duct and to measure the flow rates and both static and total pressure heads in a rigid convergent or divergent tube of geometry for a range of steady flow rates. CHE241 Fluid Mechanics- Lab Report Flowmeter Measurement Apparatus.

The Objectives of the experiment are Identify typical values of Reynolds Number for the laminar transitional and turbulent regimes of flow in a pipe with a circular cross-section of diameter. International Organization of Standards ISO 5167-2 2003. LIFLUBA Basic Fluid Mechanics Integrated Laboratory.

Always wear shoes before entering lab. For Reynolds number less than 2100 the pipe flow will be laminar. Fluid Mechanics Lab Report CED UET-P Muhammad Bilal Experiment 10 To determine the relationship between head loss due to friction and velocity for flow of water through smooth bore pipe Objectives To study and develop laminar flow To study and develop turbulent flow To study head losses in pipes at different velocities Theory.

Tables of raw data. Then the discharge pipe was opened. McGraw-Hill Book New York NY.

Many of the unknowns have a very disagreeable odor. Bansal nd Chapter 8 flow measurement A Textbook of Fluid Mechanics Miller RW 1996 Flow Measurement engineering Handbook 3Rd ED. An orifice plate beta ratio of 06 means that the orifice plate bore diameter is 60 of the pipe internal diameter.

On one chart plot a graph of x values y-axis against yh 12 values x-axis for each test. Your report should include the following. For example in a lab room with a required air exchange rate of 2000 cubic feet per minute CFM if that room has just one fume hood which vents air at a rate of 1000 square feet per minute then closing the sash on the fume hood will simply cause the lab rooms air handler to increase from 1000 CFM to 2000 CFM thus resulting in no net.

Width of rectangular notch b 003 m angle of V-notch 90Calculate discharge Q and head h for each experiment and record them in the Result TablesFor calculation purposes the depth of the water above the weir is the difference between each. Do not touch anything without the permission of instructorlab assistant. The flow coefficient is found to be stable between beta ratio of 02 to 07 below which the uncertainty in flow measurement increases.

To minimize this odor in the lab be sure to rinse used pipets with a LITTLE acetone in the hood before disposing of them in the boxes in the waste hood labeled contaminated pipets. Use the template provided to prepare your lab report for this experiment. American Society of Mechanical Engineers ASME.

Inside the Venturi-Meter a pressure difference is created by changing the flow passage cross sectional area while the pressure difference helps in determination of the discharge flow rate through the pipe line. The following dimensions from the equipment can be used in the appropriate calculations. Turbulent occur when Reynolds number is above 4000.

Impact Of A Jet Lab Report - Free download as Word Doc doc docx PDF File pdf Text File txt or read online for free. Read carefully the lab manual before performing experiments. Founded in 2002 by Nobel Laureate Carl Wieman the PhET Interactive Simulations project at the University of Colorado Boulder creates free interactive math and science simulations.

However this cannot be achieved experimentally due to the errors made during the experiment.

Experiment 6 Pipe Friction Loss In A Smooth Pipe